brunofarad:


visit my profile sir

HsLBroker:
A home is gotten when you look for comfort based on your fantasy, but a shelter is a necessity, and a building becomes a shelter when it can prevent rain,water,sun, strong wind and other climatic elements from affecting the occupants- human,animal, living and dead loads with personal effects.

As far as I am concerned the moment you have your roof placed on a building, other things are important but they are basically needs. You can’t move into a house without a roof , but we have seen people living in a house with no window or makeshifts windows covered with ordinary bags and cardboards.

So it is very important to calculate the dimension of the true length of a roof members. These dimensions are essential to determine the accurate span of Rafter, Wall plate, Tie beam, King Post, Overhang, Purlins, fan struts etc.

Residential timber-framing construction clearly differentiate between spacing and span Spacing the centre-to-centre distance between structural members, unless otherwise indicated.

Span the face-to-face distance between points capable of giving full support to structural members or assemblies. In particular, rafter spans are measured as the distance between points of support along the length of the rafter and not as the horizontal projection of this distance.

Single span the span of a member supported at or near both ends with no intermediate supports.

Continuous span the term applied to members supported at or near both ends and at one or more intermediate points such that no span is greater than twice another.

Span/length calculation for roof members.

As can be seen the span of the rafter in the figure below is not quite in agreement with the Code but we will use the figures for the rafter span as calculated below.

Wood/ timber are sawn into various sizes amongst are

2” by 2” i.e 50mm by 50mm

2” by 3” i.e 50mm by 75mm

2” by 4” i.e 50mm by 100mm

2” by 6” i.e 50mm by 150mm

3” by 4” i.e 75mm by 100mm

3” by 6” i.e 75mm by 150mm
From the picture above you can see the height of the roof of building and the length and breadth of building is already shown in the floor plan, so left to be known is the rafter or the fall ‘x’ as shown in diagram above.

Remember the Pythagoras theorem in secondary school days used in calculating the longest part of a right angle triangle.

The numbers of wood to be calculated also depends on spacing for the purpose of this exercise, we are using the format in diagram above as our specifications for our calculations.

For ceiling noggins of 600mm centers it simply means the wood are nailed 600mm apart, so add the breadth of plan and 600mm as overhangs both sides i.e 7,800mm or 7.8m +1200mm or 1-2m=9meters

Then divide by 0.6m=15pcs of 16.975m of 50 by 50.

For the longitudinal portion, 16.975+1.2m(the overhangs of 0.6m both sides)=18.175m then divide by 0.6=31 pcs of 9m of 2” by 2” ( Note how the length on one side is used to calculate the pieces/numbers of wood required for the length of the other side)

So to know the number of 2 by 2 to buy in the market for the ceiling noggins-

18.175m x 15pcs=273m of 2” by 2”

9m x 31pcs=279m of 2” by 2”

Total=552m

In the market, the wood comes in 3.6m per piece

So 552/3.6=153 pcs of 2” by 2” timber to buy in the market for ceiling noggins.

WALL PLATE is the timber/wood that are placed on top of blocks or roof beams as the case may apply, so for the fastest way to calculate this, is to add the entire walls length and divide by 3.6m to know the numbers of pieces you need. I am using approximately 100m.

So for 100m, divide by 3.6=28pcs of 3” by 4” or 75mm by 100mm to purchase in the market for timber named wall plate.

For FACIAL BOARD, remember the length and breadth of the plan of the building with its overhangs of 0.6m each, so add the perimeter

9m+9m+18.175m+18.175m=54m

Divide 54m by 3.6m=15pcs of 1” by 12”

For TIE BEAM, going by the section, it was recommended that we lay the timber named tie beam which is 2” by 6” or 100mm by 150mm at 1.2m centers apart. So what we need to do is to follow the same format used in calculating the ceiling noggins but it is going to span only the breadth of 7.8m only.

So divide 18.175m by 1.2m centers (spacing)

=15pcs of 7.8m =117m, then divide by 3.6m to know the numbers to buy/purchase in market.

117/3.6=32pcs of 2 by 6 of wood termed as tie beam to buy in the market.

STRUTS are a bit complex to calculate, they are the members placed diagonally as shown in diagram to connect the rafter with tie beams. We can use the numbers of tie beams and multiply by 2-

i.e 32 pcs multiply by 2=64 pcs of 3 by 4 or 75mm by 100mm termed as struts to be bought in the market.

For RAFTER, check the height of roof and the breadth of plan to determine the rafter which is the falling portion of the roof (except is already given from the section)

Lets take the height of the roof as 3.5m and the breadth of plan plus overhang is 9m.

HsLBroker:
hardwood available for sale

HsLBroker:
.

ak22:
Sorry for using your thread @HsLBroker

Let us handle your precast parapet design

Call 08100718479

HsLBroker:
Hardwood available for sale

HsLBroker:
.

HsLBroker:
.

Kingimade:
Nice work.

Please what are the prices for the hardwood and how can i reach you?

HsLBroker:
thanks, 08182481552 or lifelightproperties@gmail.com

2x2x12@N400
2x3x12@N500
2x4x12@N600
2x6x12@N950
3x4x12@N850
1x12x12@N1, 800

Kingimade:
Nice work.

Please what are the prices for the hardwood and how can i reach you?

Kingimade:
Nice work.
Please what are the prices for the hardwood and how can i reach you?

HsLBroker:
still available for sale 2x2, 2x3, 2x4, 2x6, 3x4, 2x6, 1x12 call 08182481552 for more information

HsLBroker:
.

samoskyz:
Port Harcourt!!!
We supply all kinds of building materials to construction sites within and outside rivers state port harcourt, like sharp sand, 30 tons of chippings, 9 inches blocks, 6 inches blocks, 5 inches blocks without hole, hardcore stone, stone base zero 50, trailer load of cement which is 900 bags. And we deliver before payment. Price list: Sharp sand 30k, Hardcore stone 50k per trip, Stone base zero 50 200k for 30 tons, 30 tons of chippings 260k,  9 inches block 160 naira per block,  6 inches block 130 naira per block,  5 inches block without hole 150 naira per block, Trailer load of cement which is 900 bags 2.350 million naira.
All our supplies comes directly from its source. We deals with both individuals and companies (construction companies, developer and etc.. )
Call us today on 08069801335 or 08159309557 For an order... a trial will definitely convince you and remember that "integrity is our watchword".

Regards,
Samuel. [color=#990000][/color]

HsLBroker:
.