HsLBroker:
2x2
woods are mainly use for ceiling noggin, but if you are installing stone coated roofing sheets to cover your roofing wooden carcass, full size 2x2 is suitable too for your purling(note that I said full size 2x2 not solo) because the full sizes 2x2 is what most saw mill now saw or sell for 2x3.

2x3 is mainly use for purling or latt according to how the carpenters call it. (Purling or latt is the vertex level point on the roof where the roofing sheets will be lay)

2x4 is use for the tie beams, joining or bracing, Ridges and finally ridges construction on the roofing carcass

2x6 is for king post

3x4 is use for the wall plate

of course everyone should know facial board is 1x12 but for aesthetic design on the roof it will be reduce to 1x10.

Facial board is mainly use when there is no parapet attach to the block roofing level.

Thanks

HsLBroker:
.....

HsLBroker:
Still available for sale

HsLBroker:
A home is gotten when you look for comfort based on your fantasy, but a shelter is a necessity, and a building becomes a shelter when it can prevent rain,water,sun, strong wind and other climatic elements from affecting the occupants- human,animal, living and dead loads with personal effects.

As far as I am concerned the moment you have your roof placed on a building, other things are important but they are basically needs. You can’t move into a house without a roof , but we have seen people living in a house with no window or makeshifts windows covered with ordinary bags and cardboards.

So it is very important to calculate the dimension of the true length of a roof members. These dimensions are essential to determine the accurate span of Rafter, Wall plate, Tie beam, King Post, Overhang, Purlins, fan struts etc.

Residential timber-framing construction clearly differentiate between spacing and span Spacing the centre-to-centre distance between structural members, unless otherwise indicated.

Span the face-to-face distance between points capable of giving full support to structural members or assemblies. In particular, rafter spans are measured as the distance between points of support along the length of the rafter and not as the horizontal projection of this distance.

Single span the span of a member supported at or near both ends with no intermediate supports.

Continuous span the term applied to members supported at or near both ends and at one or more intermediate points such that no span is greater than twice another.

Span/length calculation for roof members.

As can be seen the span of the rafter in the figure below is not quite in agreement with the Code but we will use the figures for the rafter span as calculated below.

Wood/ timber are sawn into various sizes amongst are

2” by 2” i.e 50mm by 50mm

2” by 3” i.e 50mm by 75mm

2” by 4” i.e 50mm by 100mm

2” by 6” i.e 50mm by 150mm

3” by 4” i.e 75mm by 100mm

3” by 6” i.e 75mm by 150mm

HsLBroker:
....

HsLBroker:
..

HsLBroker:
A home is gotten when you look for comfort based on your fantasy, but a shelter is a necessity, and a building becomes a shelter when it can prevent rain,water,sun, strong wind and other climatic elements from affecting the occupants- human,animal, living and dead loads with personal effects.

As far as I am concerned the moment you have your roof placed on a building, other things are important but they are basically needs. You can’t move into a house without a roof , but we have seen people living in a house with no window or makeshifts windows covered with ordinary bags and cardboards.

So it is very important to calculate the dimension of the true length of a roof members. These dimensions are essential to determine the accurate span of Rafter, Wall plate, Tie beam, King Post, Overhang, Purlins, fan struts etc.

Residential timber-framing construction clearly differentiate between spacing and span Spacing the centre-to-centre distance between structural members, unless otherwise indicated.

Span the face-to-face distance between points capable of giving full support to structural members or assemblies. In particular, rafter spans are measured as the distance between points of support along the length of the rafter and not as the horizontal projection of this distance.

Single span the span of a member supported at or near both ends with no intermediate supports.

Continuous span the term applied to members supported at or near both ends and at one or more intermediate points such that no span is greater than twice another.

Span/length calculation for roof members.

As can be seen the span of the rafter in the figure below is not quite in agreement with the Code but we will use the figures for the rafter span as calculated below.

Wood/ timber are sawn into various sizes amongst are

2” by 2” i.e 50mm by 50mm

2” by 3” i.e 50mm by 75mm

2” by 4” i.e 50mm by 100mm

2” by 6” i.e 50mm by 150mm

3” by 4” i.e 75mm by 100mm

3” by 6” i.e 75mm by 150mm

HsLBroker:
.........

HsLBroker:
A home is gotten when you look for comfort based on your fantasy, but a shelter is a necessity, and a building becomes a shelter when it can prevent rain,water,sun, strong wind and other climatic elements from affecting the occupants- human,animal, living and dead loads with personal effects.

As far as I am concerned the moment you have your roof placed on a building, other things are important but they are basically needs. You can’t move into a house without a roof , but we have seen people living in a house with no window or makeshifts windows covered with ordinary bags and cardboards.

So it is very important to calculate the dimension of the true length of a roof members. These dimensions are essential to determine the accurate span of Rafter, Wall plate, Tie beam, King Post, Overhang, Purlins, fan struts etc.

Residential timber-framing construction clearly differentiate between spacing and span Spacing the centre-to-centre distance between structural members, unless otherwise indicated.

Span the face-to-face distance between points capable of giving full support to structural members or assemblies. In particular, rafter spans are measured as the distance between points of support along the length of the rafter and not as the horizontal projection of this distance.

Single span the span of a member supported at or near both ends with no intermediate supports.

Continuous span the term applied to members supported at or near both ends and at one or more intermediate points such that no span is greater than twice another.

Span/length calculation for roof members.

As can be seen the span of the rafter in the figure below is not quite in agreement with the Code but we will use the figures for the rafter span as calculated below.

Wood/ timber are sawn into various sizes amongst are

2” by 2” i.e 50mm by 50mm

2” by 3” i.e 50mm by 75mm

2” by 4” i.e 50mm by 100mm

2” by 6” i.e 50mm by 150mm

3” by 4” i.e 75mm by 100mm

3” by 6” i.e 75mm by 150mm

HsLBroker:
.....

HsLBroker:
...

HsLBroker:
you are highly welcome sir.

UK nails N8, 500, Chinese N9, 500 per bag, yes i use them sir, the Oja agba or roofer holder is mainly apply to perimeter wall of the building sir, Oja agba is not necessary again once there is cutter rod inside the parapet sir.

DorlanEyes:




HSLBroker, Pls what does a cutter rod look like?

HsLBroker:
Still available for sale

Bodlade:
CURRENT PRICES FOR MATERIALS

Cement Supplies (Dangote)
2600 per bag (transport inclusive for 300 bags upward)
2650 per bag (transport inclusive for 200 bags)

Granite Supplies
30 tons to Redeem Camp: =N=116,000
30 tons to Mowe/Ibafo : =N=120,000
30 tons to Berger Lagos: =N=125,000
30 tons to Lagos Mainland: =N=128,000
30 tons to Lagos Island: =N=140,000

Stone Dust Supplies
30 tons : 78,000

Sharp Sand Supplies
20 tons to Redeem Camp: =N=45,000
20 tons to Mowe/Ibafo : =N=47,000
20 tons to Berger Lagos: =N=47,000

Dagbolu Sand Supplies
20 tons to Redeem Camp: =N=35,000
20 tons to Mowe/Ibafo : =N=35,000


Plaster Sand Supplies
20 tons to Redeem Camp: =N=32,000
20 tons to Mowe : =N=33,000
20 tons to Ibafo : =N=36,000
20 tons to Berger Lagos: =N=38,000

Fillings/Laterite Supplies
20 tons to Redeem Camp: =N=15,000
20 tons to Mowe : =N=18,000
20 tons to Ibafo : =N=20,000
20 tons to Berger Lagos: =N=23,000

1x12 wood= 1250
2x2 wood=250
2x3 wood=350
Bamboo=200
Nail=9000 per bag

Iron rod
12mm= 150,000/ton
16mm= 150,000/ton
10mm= 155,000/ton

For your supplies ( Full & accurate )
Call Sorted Impact Company on
08020535537, 08077257811
Address: Flat 4, Delta province chalet, Redeem camp.


**INTEGRITY IS OUR WATCHWORD**

nwaonyeze001:




Is this price still viable....if No, please can you give the current price for all this

Thanks