Chekitaut:
Please be informed no imported Iron Rod in Nigeria. All are produced here, we hv some bad steel call Local-Local pls take note. Don't be decived.

Dijita:



I am not a plumber but I am going to suggest you engage the service of a plumber. The Picture one did not give room for one to bypass the filter if you decided for whatever reason e.g. lack of fund or filter availability or change of mind
picture B is what I have and it allow me to bypass the filter when my madam decided she preferred bottle water to the filtration . it is just a matter off pulling up A and closing up B and C

sako28:


Oga I hail,
From Abakaliki that I don't know, but from Cross river is +/- 330 to PH. Due to bad road ur granite can be delayed by 1 or 2 days.

However, There is a Chinese company after Port harcourt Refinery that crush and sell granite of different size. The rate is 10k per tonne, then u negotiate transport to ur site separately. E.g to deliver to Ada George area of PH is like 40-45k. To Uzoba and Choba area is like 50k. Try to negotiate the transport to ur best ability.

Hope this help.

sako28:



Chipping in PHC is gold ooo. A times due to stress from calabar or Abia, we just go for the Chinese one. U see what u buy and leave. 20k transport is may be to Oyingbo side. Any move beyond aba road na 30k above.

Chekitaut:
i have move chippings from Edo to PH...

diordaves:


Ceiling board:

https://www.nairaland.com/6197857/latest-prices-pop-cement-asbestos

Beframia:

Going by my experience last week where a portion of my living room PVC ceiling collapsed, I'm not going to advise you use a PVC if the building is yours. Except it's a temporary measure pending when you can afford a better alternative like a POP or the like.

Chekitaut:
Port-Harcourt pick Granite from Calabar no Quarry in PH.

Transportation cost from Calabar is over 170k for 30tons

jennann:
Goodmorning everyone. I am a newbie in this section and would want to seek clarification on this issue.

My family is building a story building of four flats of 3 bedrooms each. We are at the decking stage now. However, the supervisor handling it is advising us to use 10mm steel rods for this decking as this steel rod is stronger than 12mm rod and can carry the weight comfortably. This is different from what I know with my little building knowledge.
So I decided to come here to seek expert opinion on this.

Thankyou for expected comments as I know I d definitely get the best advice here.

sako28:


Oga I hail,
From Abakaliki that I don't know, but from Cross river is +/- 330 to PH. Due to bad road ur granite can be delayed by 1 or 2 days.

However, There is a Chinese company after Port harcourt Refinery that crush and sell granite of different size. The rate is 10k per tonne, then u negotiate transport to ur site separately. E.g to deliver to Ada George area of PH is like 40-45k. To Uzoba and Choba area is like 50k. Try to negotiate the transport to ur best ability.

Hope this help.

sako28:



Chipping in PHC is gold ooo. A times due to stress from calabar or Abia, we just go for the Chinese one. U see what u buy and leave. 20k transport is may be to Oyingbo side. Any move beyond aba road na 30k above.

Jasobry:
This wooden door is made in locally... I want to use same design for my entrance door. How cool is it?

Nettuno:

That is what I think I can afford. Pop is on the high side for me.

n3xt:
This is still PVC

KolaShangOne:


Don't sound so sure if you're not sure of something bros.

When last were you in Port Harcourt? I'm telling you I personally used my 2 legs to buy granite and you're insinuating that it's a lie? That's disrespectful please.

EgunMogaji2:


What is PVC? Not the ceiling for sure.

n3xt:


The marked area is 100% PVC.

sako28:



Oga kola, no is not disrespect oo. U are an elder here. I stay in PH. And that the reality we face here. I Just got 25 tones last week from the Chinese company at the rate of 10k per tonne. That why in PHC some people you Periwecule shell to mix cement and sand to cast floor and some little work. What compensate us small in PHC is that will spend less than 150k to get bolehore.

EgunMogaji2:


Okay then. I’m assuming you did the install?

n3xt:


I have one like this on here. I have to check though.

We use the combination of amoula pvc and POP.

In actually fact, one of my latest work in Chevron had PVC elements. The ceiling is not the conventional designs we see around. I’ll try to share now.

The project is underway.

EgunMogaji2:


Speaking on the first pic alone because it looks like the abroad then I’ll wager that you’re looking at 100% wood, not PVC. Exhibit 1

No home inspector will approve a kitchen with PVC in at least California due to its fire performance properties.

You’ll find PVC on the exterior on low budget builds and in non fire prone areas. Exhibit 2

I’m still open minded to learn because knowing you, you’ll dig up a interview of the architect/builder confirming that it’s PVC

Nettuno:
Good day Experts,

Please how many bundles of Nigerian PVC do I need for the ceiling of a standard 3 bedroom bungalow? How much is the current cost?
Thanks .

Jasobry:
This wooden door is made in locally... I want to use same design for my entrance door. How cool is it?

davodyguy:

Original prag inverter of 2.0KVA cost less than ₦300k

n3xt:


Smiles. I’ll send you samples if you want or give you the link to the Chinese company selling it for further discussion.

My concrete mixer drum sef is PVC How about that?
The world changed already.

Chekitaut:
Rain is very powerful can destroy any form of Gerard with time... You will only carry out maintenance culture simple.