PEUGEOT 407 - THE MOST COMMON PROBLEMS AND FAILURES

10/02/2018 Peugeot , Used cars

What are the most common problems and failures of the Peugeot 407 and how to solve them?
Peugeot 407 - ALL MODELS
PROBLEM - Noise from front wheel bearings.
CAUSE - Poor construction of front wheel bearings. Applies only to wheel bearings manufactured by NSK.
REPAIR - Replace the NSK front wheel bearing with SNR type.

Peugeot 407 - ALL MODELS
PROBLEM - Punching from the front suspension when driving in curves or parking.
CAUSE - Loose upper hinge (s) on front hub bracket (s).
REPAIR - Tighten the front hub bracket upper hinge to 200 Nm. Use a special tool.

Peugeot 407 - ALL MODELS
PROBLEM - Creaking from the front suspension on uneven surfaces.
CAUSE - Excessive friction between the upper front suspension joints.
REPAIR - Remove the front suspension struts. Remove the friction washer and lubricate the bearings.

Peugeot 407 - ALL MODELS
PROBLEM - The front fog lights cannot be turned on or off. The rear fog lights cannot be switched on or off.
CAUSE - Improper version of the combination switch.
REPAIR - Set a modified combination switch.

Peugeot 407 - ALL MODELS
PROBLEM - The wipers turn on for no reason when the vehicle is unlocked or the door is opened.
CAUSE - Defective windshield wiper motor.
REPAIR - Install the modified windshield wiper motor.

Peugeot 407 - ALL MODELS
PROBLEM - Startup error. The engine does not start. The fuse has blown. Fuse box / relay plate in engine compartment.
CAUSE - Insufficient allowable fuse load.
REPAIR - Inspect the starter electrical wiring for damage and repair if necessary. Replace fuse F8 (15A) in the fuse box / relay board in engine compartment 1 with fuse 25A. Check the operation of the engine starter.

Peugeot 407 - ALL MODELS
PROBLEM - One or both headlights do not work.
CAUSE - Weak mass connection to light (s).
REPAIR - Test electronics and mechanics components (as needed) to eliminate other possible causes. If no fault is found: repair the electrical installation with the headlights using the repair kit.

Peugeot 407 - ALL MODELS
PROBLEM - The airbag control indicator illuminates. Error codes stored in the SRS control module error memory.
CAUSE - Open coil airbag coil circuit.
REPAIR - Replace the multifunction switch.

Peugeot 407 - ALL MODELS WITH TEMPOMATOM
PROBLEM - Cruise control does not work and is occasionally turned off.
CAUSE - Brake pedal position (BPP) switch defective.
REPAIR - Check that the distance between the adapter and the surrounding components is satisfactory. Install the modified brake pedal position (BPP) switch. Install the adapter assembly to the brake pedal position switch (BPP) and the existing assembly. Secure the adapter assembly with the hook.

Peugeot 407 - MODELS WITH CODE DAM 11213
PROBLEM - The ESP control indicator illuminates
CAUSE - Water enters the ABS wheel speed sensor (s).
REPAIR - Perform a diagnostic check to confirm the error. Replace the faulty ABS wheel speed sensor (s).

Peugeot 407 - MODELS WITH CODE DAM 11347CJ
PROBLEM - The brake pad wear indicator light illuminates intermittently.
CAUSE - Short circuit at the brake liner wear sensor connection.
REPAIR - Remove 50 mm of insulation from the electrical installation. Cut the ground wires at the connector and connect using thermal connectors.



Peugeot 407 1.6 HDI
PROBLEM - Turbocharger (TC) oil leak. Loss of strength. Engine / turbocharger (TC) whistling sound.
CAUSE - Inspect the TC intake pipe for cracks.
REPAIR - Replace the TC suction pipe.

Peugeot 407 DIESEL MODELS WITH SOIL FILTER
PROBLEM - The engine failure indicator (MIL) light is on. Loss of strength. Whistling from the turbocharger (TC). Too much exhaust fumes.
CAUSE - Internal turbocharger (TC) fault.
REPAIR - Inspect the engine for internal damage and repair as needed. Install a new turbocharger (TC).

Peugeot 407 ALL MODELS WITH AM6 GEARBOX.
PROBLEM - The selector lever cannot be moved from the 'P' position when using diagnostic equipment.
CAUSE - Software error in Transmission Control Module (TCM).
REPAIR - The diagnostic procedure must not be started before the following: Turn the ignition ON. Turn the ignition OFF for 50 seconds. Turn the ignition ON. Without switching off the ignition, run the diagnostic procedure. Clear the error codes.

Peugeot 407 - ALL MODELS
PROBLEM - The fuel filler flap does not open.
CAUSE - Improper version of the fuel filler cap and spring to open the cap.
REPAIR - Replace the fuel filler cap housing.



Peugeot 407 - ALL MODELS
PROBLEM - Poor operation of the heating fan / air conditioning motor on vehicles that have traveled less than 10000 km since the cabin filter was replaced. Reduced airflow inside the vehicle.
CAUSE - Cabin filter blocked due to improper filter version.
REPAIR - Install a modified cab filter.



Peugeot 407 - ALL MODELS
PROBLEM - Vibration on the power steering column in curves or when parking.
CAUSE - The air in the power steering fluid creates foam. Insufficient fluid in the power steering fluid reservoir, although it is on the oil dipstick on the MAX mark.
REPAIR - Top up the power steering fluid 25 mm above the MAX mark.

Peugeot 407 - DIESEL MODELS
PROBLEM - The engine coolant temperature control indicator illuminates, but the engine temperature gauge reads normal. Switching on the air conditioner affects the operation of the engine coolant temperature control lamp.
CAUSE - Faulty engine coolant fan motor relays (3).
REPAIR - Install all three new relays.

Peugeot 407 - DIESEL MODELS WITH CODE - DAM
PROBLEM - Poor start. The engine failure indicator (MIL) illuminates.
CAUSE - The high pressure fuel pump is losing pressure.
REPAIR - Replace the high pressure fuel pump.



Peugeot 407 - ALL MODELS 2.0 HDI
PROBLEM - Engine Malfunction Indicator Lamp (MIL) illuminates. Error codes recorded in the engine computer error memory (ECM): turbocharger pressure error.
CAUSE - Turbocharger (TC) ring stuck.
REPAIR - Install a new turbocharger (TC).

Peugeot 407 2.0 HDI
PROBLEM - Engine Malfunction Indicator Lamp (MIL) illuminates.
CAUSE - Faulty intake air temperature (IAT) sensor.
REPAIR - Install a new IAT sensor.



Peugeot 407 - MODELS WITH CODE DW
PROBLEM - Malfunction at idle during cold start.
CAUSE - Engine computer software (ECM) error.
REPAIR - Test electronics and mechanics components (as needed) to eliminate other possible causes. If no error is found: Reprogram the engine computer (ECM) with the upgraded software.

Peugeot 407 - MODELS WITH CODE DW
PROBLEM - Creaking from the front suspension on uneven surfaces.
CAUSE - Excessive friction between the upper front suspension joints.
REPAIR - Remove the front suspension struts. Remove the friction washer and lubricate the bearings.

Peugeot 407 - MODELS WITH CODE EW
PROBLEM - Noise from the front of the vehicle at a constant speed. Gradual wear on the edge of the front tires.
CAUSE - Incorrect front suspension springs installed.
REPAIR - If the front suspension spring identification mark is incorrect, install new front suspension springs. Check and adjust the geometry of the front wheels. Replace tires if necessary.

Peugeot 407 - MODELS WITH CODE DW
PROBLEM - Noise from the rear of the vehicle at a constant speed. Gradual wear on the edge of the rear tire.
CAUSE - Rear suspension curved springs installed.
REPAIR - Check the color ID on the rear suspension springs: Blue ID: For EW12J4 (3FY / 3FZ) engine. Purple identification code: For DT17TED4 (UHZ) engines. White identification mark: For ES9A (XFV) engine. If the rear suspension spring identification mark is incorrect, install new rear suspension springs. Check and adjust the alignment of the rear wheels. Replace tires if necessary.

Peugeot 407 - MODELS WITH CODE DT17TED4 (UHZ)
PROBLEM - The engine fault indicator light is on. The engine loses power and works poorly.
CAUSE - Damaged electrical wiring of the engine near the air filter assembly.
REPAIR - Repair or replace the engine electrical wiring assembly as needed.

Peugeot 407 - MODELS WITH CODE ES9A (XFV)
PROBLEM - Engine Malfunction Indicator Lamp (MIL) illuminates. The engine jerks and loses power.
CAUSE - Coil error.
REPAIR - Check the coils for correctness and replace if necessary.


https://mlfree.com/en/peugeot-407-najcesci-kvarovi/

Someone might find this useful

thanks

What causes the noise gbam when I enter a port hole when driving? Shock changed recently, especially from the front suspension

With all these issues.... Just avoid the vehicle

Beautiful motor

Does it apply to the 307 and 308?

sexyto:
Does it apply to the 307 and 308?

I don't know, I'll check up on them

MASTAkiLLAh:
I don't know, I'll check up on them

I'll like to read your response from your findings.

Praxtech:
With all these issues.... Just avoid the vehicle

and buy which one? Please suggest.

1Alex:
and buy which one? Please suggest.

all cars have their issues, just get something new or a well maintained fairly used. Go with a sound and experienced mechanic for inspection and enjoy your car for the years you wish to use it

MASTAkiLLAh:
all cars have their issues just get something new or a well maintained fairly used. Go with a sound and experienced mechanic for inspection and enjoy your car for the years you wish to use it

yeah. I thought the guy I quoted would mention a particular car, then I would tell him the bolded.

Meanwhile I have been using Peugeot 407 since 2017. If I sell It, I will buy another 407.

Bro is it manual or automatic?

1Alex:
yeah. I thought the guy I quoted would mention a particular car, then I would tell him the bolded.

Meanwhile I have been using Peugeot 407 since 2017. If I sell It, I will buy another 407.

olisafincy:
Bro is it manual or automatic?

automatic, then later converted to manual