Are you currently looking for these Chemicals and Materials. If so contact Cj on 08085833799. 5 Asa Afariogun Street, Ajao estate Lagos.

Scroll down

Plaster insolating cream

+ Insolating layer for keeping the skin separated during plaster casting
+ Lines produced with a copying pen or grease pen are clearly visible on the negative
+ When applied to the skin, an even parting film is immediately created by the heat of the body
+ Does not smear, drip or stick


Plaster parting agent
+ For isolating plaster from plaster
+ For isolating plaster from thermoplastics

Stucco plaster
+ For fabricating positive models in orthopaedics technology
+ Grain coarser than with alabaster modelling plaster
+ Fast curing
+ High strength

Alabaster modelling plaster
+ For fabricating positive models in orthopaedics technology
+ Manufactured with selected raw stones, finely ground and very pure, with high degree of
whiteness
+ After curing, the surface is smooth and ideally suited for modelling

Synthetic plaster
+ For accurate visual models and mould construction
+ Very pure raw material
+ High capacity for pressing out and absorbing water
+ Above-average hardness

Latex parting agent
+ For insolating dry plaster models
+ A thin latex skin forms and serves as a separating layer with excellent separating properties
+ Easy to process

Grease pens
+ For marking damp plaster casts and models
+ For marking lines, e.g. on thermoplastics
+ For paper, glass, plastic, metal
+ Easily removable, therefore good alternative to permanent markers
+ Lead made of high-quality pigments
+ Can be applied with water
+ Various colours available

Pedilen duplicating foam

+ Two-component plastic which is outstanding for making quick prosthetic socket duplications
+ It also copies undercuts precisely and can be easily removed
+ Further modifications possible, e.g., can be sanded or 636K17 Otto Bock Lightweight Putty
can be applied
+ Sensitive to moisture


Hardener for pedilen rigid foams

+ Hardener for all Pedilen rigid foams and Pedilen duplicating foams
+ Hardener has no influence on the swelling factor, foam determines swelling factor

Carbon Graphite

+ For high-strength, very thin orthoses on a thermoplastic material basis
+ Matrix: TPU
+ Can be thermoformed under pressure
+ High tensile strength
+ Suitable for surfaces
+ Paintable
+ Potentially adhesive
+ Can be welded with components of the same matrix
+ Clean processing
+ No special storage requirements (e.g. no cooling)
+ Moderate thermoforming temperature: approx. 220 °C



Silicone foil

+ Processing aid for TP.C
+ Temperature stable
+ Highly elastic
+ Processing temperature: max. 240 °C (464 °F)



ThermoLyn Pedilon

Low-temperature polyester
+ For the fabrication of orthoses without preparing a plaster cast or model
+ Mobile applications, ideal for hospital use and for providing instant patient fittings
+ Thermoformable at low temperatures
+ Eliminates the time-consuming tasks of fabricating casts and models
+ Very high adhesive strength
+ High restoring capacity when reheated
+ Temperature recommendation: heat in water bath at 60°C/140°F




Silicone grease 400, medium
+ Corrosion protection for plug connections, e.g. Myo, E-MAG Active (cable plug)
+ Corrosion protection, e.g. for drive units
+ For the planetary gear set of the drive unit in the area of the upper limbs
+ For isolating components with lamination technique
+ Very good resistance to heat and cold
+ High resistance to ageing
+ Good film-forming ability

Pedilen rigid foam 100
+ For fabricating rehabilitation seating systems and for compensating forms
+ Fast and safe processing with hand mixing procedure
+ Precise duplication
+ Penetration hardness (for 10% linear compression): approx. 0.63 N/mm²
+ No shrinkage
+ Easy to refinish in the cured condition, e.g. sanding, lamination
+ Sensitive to moisture

Pedilen flexible foam 150

+ For making flexible cosmetic body compensations
+ Fast and safe processing with hand mixing procedure
+ Precise duplication
+ Penetration hardness (for 10% linear compression): approx. 0.02 N/mm²
+ No shrinkage
+ Easy to refinish in the cured condition, e.g. sanding, lamination
+ Sensitive to moisture



Hardener for Pedilen flexible foams

+ Hardener for 617H35 Pedilen Flexible Foam 150 and for 617H42 Pedilen Flexible Foam 300
+ Hardener has no influence on the swelling factor, foam determines
swelling factor

Flexible foam, component a
+ For producing two-component polyurethane foams
+ For customised orthopaedic precision parts
+ Fast and safe processing with hand mixing procedure
+ Low weight
+ Precise duplication
+ Penetration hardness (for 10% linear compression): approx. 0.01 N/mm²
+ No shrinkage
+ Easy to refinish in the cured condition, e.g. sanding, lamination
+ Sensitive to moisture




Flexible foam, component b
+ For producing two-component polyurethane foams
+ For customised orthopaedic precision parts
+ Fast and safe processing with hand mixing procedure
+ Low weight
+ Precise duplication
+ Penetration hardness (for 10% linear compression): approx. 0.01 N/mm²
+ No shrinkage
+ Easy to refinish in the cured condition, e.g. sanding, lamination
+ Sensitive to moisture