baldwin84:

hello oga guru...I use 2004 Mitsubishi lancer. d oil sump hit ground while traveling on Sunday afternoon. I looked for mechanic and panel beater to solve d problem but we couldn't get d appropriate oil so I opted to forte oil visco. immediately d engine oil enter d motor start smoking but not too much. Then I took it to my mechanic to solve d issue of smoking but he told me not to change d engine oil but just to add oil treatment. after putting d oil treatment d motor smokes badly..Please what is d solution?

What oil were you using before?

Neyohpinpin:
good afternoon Guru......

I just noticed that my Accord 05 A/C does not really cool well during the day ....but cools very well to cold sef at night .... is there anything wrong, if yes ,please what can I do please??

Check the operation of your cooling fans. It should come on ( the two of them) when you switch on the AC.

bleedingpile:
Hello guru,
Great job you are doing here. God bless!

Please, I am a novice. Just got myself a Nissan xterra 2000 vehicle few days ago. Please, could you be kind and tell me things I need to know, the diy on my part, the changing of oil, the kind and types of engine oil,break oil etc that are healthy this kind?
Also, battery voltage , general maintenance and the pro and cons ?. Your reply would be so appreciate -----don't even have an idea where to start and go from here.

Please help!

Not a bad car. It has a rugged engine. read your owners manual for all these info( you will find them there) and you are good to go.

babyboy4every1:
oga guru. I bought almera tino some six mnth ago. It has started shorting oil &producing little flames wen start in d mrning bt stop imdtly. Wht cld be d prblm wt a tokunbo car. Also, i scanned it &detects d 02 sensors. Wht is d implctn of d 02 sensors if i didnt change it.

Valve stem seals could be bad. replace them and get back to me.

here!

MotorGuru:


rebuilding would have been a better option , but with the current level of available expertise, please toks is better.
What to look out for:
1.Check coolant passage ways and ensure you do not see any chalk- like coating. if you do, that engine has been used in Nigeria Before and
water was used as coolant.
2.Check the interface between Top cylinder& engine block and ensure that graphite(paper as they call it) gasket has not been used.
3. check all gaskets and ensure it has not been supported or replaced by Gasket maker(Black or white gum). Anywhere such was originally sued from factory, it should have a slight yellowish tint to it.
4. Check all bolts and be sure there is no spanner marks(evidence that is might have been slackened before)
5.Check engine number inscription and compare with the engine currently with your car to avoid any foul play.
6. Go with an experienced person.
7. The VIN number of the car that engine came out from is usually riveted to the engine body. copy it and run a comprehensive VIN check to have an idea of the Mileage.



Use 5W20 if the engine mileage is less than 150,000 miles( on the Toks engine)

Thanks a lot.
This will be very helpful.

Kind regards

GCFR696:


Thanks a lot.
This will be very helpful.

Kind regards

you are welcome sir.

MotorGuru:


Not a bad car. It has a rugged engine. read your owners manual for all these info( you will find them there) and you are good to go.

Thanks! though you didn't tell where that could be found but I appreciate your response.

MotorGuru:

check electrical connections to this solenoid:
if ok, replace solenoid

Please I need your contact or workshop address. Thank you.

Hello house I have a Honda Accord 2000 I need to change the compressor it is bad... But I am Confused now should I change to manual or automatic

cokegee:
Hello house I have a Honda Accord 2000 I need to change the compressor it is bad... But I am Confused now should I change to manual or automatic

There is nothing to nothing like automatical compressor on Accord 2000 ,just replace with exactly what you remove and dissallow kazeem from abusing the wiring

MotorGuru:
here!

Hello sir! There's this 03 avalon 3.0 L. I'm using atm. No CEL. Last week I filled the tank to brim and zeroed my odometer and got only 193 miles out of it till the fuel Guage turned red.
Two days ago I bought fuel of 2k/13 litres and on my dashboard it showed 38miles, but my odometer only read 18miles till fuel Guage turned red.
Problem iv noticed is that the fuel mileage reading on my dashboard drops faster than anything. From 38 miles it will drop to 30miles, from 30 to 24, 20, 15, 10, 5 and the next thing is 0 mileage but my odometer will be accurate to record for me like only 18miles and my fuel Guage turns red again.
Could it be that the fuel is pouring away somewhere cos I frequent filling station every now and then because the fuel Guage drops so fast.
Car is 250k miles, problem free vehicle cos the right fluids are used on it.
Please any suggestion/solution for this?

MotorGuru:


you are welcome sir.

good day bro. I get a high humming noise whenever AC is turned on (even at the lowest) on a 2006 rav 4. it cools very well too. Wat could be the cause.

MotorGuru:


Valve stem seals could be bad. replace them and get back to me.

God bless u &ur handiwork. Alot of kazeems everywhere in abk. Infact, most of them can nt identify where to locate d egr valve (someone told me on nrlnd 2 clean it). So, i ws so confused. All they kept saying is "u hv to ring d engine" without even considering other possible causes as u just suggested now. Where is ur workshop located? Ur contact? Or betterstill, can you recommend any engineer in abk. Thanks.

Pls I have Mazda Xedos 9 and it is extremely overheating and I've done all I could to stop it but all proved abortive and my radiator is not leaking I can't travel long distance what can I do?

Newbreed2018:
Hello sir! There's this 03 avalon 3.0 L. I'm using atm. No CEL. Last week I filled the tank to brim and zeroed my odometer and got only 193 miles out of it till the fuel Guage turned red.
Two days ago I bought fuel of 2k/13 litres and on my dashboard it showed 38miles, but my odometer only read 18miles till fuel Guage turned red.
Problem iv noticed is that the fuel mileage reading on my dashboard drops faster than anything. From 38 miles it will drop to 30miles, from 30 to 24, 20, 15, 10, 5 and the next thing is 0 mileage but my odometer will be accurate to record for me like only 18miles and my fuel Guage turns red again.
Could it be that the fuel is pouring away somewhere cos I frequent filling station every now and then because the fuel Guage drops so fast.
Car is 250k miles, problem free vehicle cos the right fluids are used on it.
Please any suggestion/solution for this?

Is your check engine light on?

Ukeachu1:



good day bro. I get a high humming noise whenever AC is turned on (even at the lowest) on a 2006 rav 4. it cools very well too. Wat could be the cause.

Could be the operation of your cooling fans (which should be normal)

another possibility is the compressor bearing going bad (cheap fix)

babyboy4every1:

God bless u &ur handiwork. Alot of kazeems everywhere in abk. Infact, most of them can nt identify where to locate d egr valve (someone told me on nrlnd 2 clean it). So, i ws so confused. All they kept saying is "u hv to ring d engine" without even considering other possible causes as u just suggested now. Where is ur workshop located? Ur contact? Or betterstill, can you recommend any engineer in abk. Thanks.

at your location i cant unfortunately.

MotorGuru:
Is your check engine light on?

No CEL Sir.

darejem2002:
Pls I have Mazda Xedos 9 and it is extremely overheating and I've done all I could to stop it but all proved abortive and my radiator is not leaking I can't travel long distance what can I do?

are your fans working? is your thermostat working? have you ever worked on your engine before? any funny coloration of your coolant?

Newbreed2018:
No CEL Sir.

Perform tuneup: Spark plug change, engine air filter, EGR/ Throttle body cleaning. 250K miles is not beans.

Also ensure that timing belt change has been performed (considering the mileage)

USE GENUINE PARTS ONLY.

MotorGuru:


Perform tuneup: Spark plug change, engine air filter, EGR/ Throttle body cleaning. 250K miles is not beans.

Also ensure that timing belt change has been performed (considering the mileage)

USE GENUINE PARTS ONLY.

Thank u so much. I'll try all of the above and see how it goes.

Please my liberty Jeep 08 shows check engine on dashboard and after scanning we found out catalytic converter and O2 sensor needs to be replaced. I bought new ones and they were replaced. Fuel consumption reduced and no more noise from exhaust but the check engine signal is still on and three new lights are on which are service 4WD and I can’t change from 2WD to 4WD Plus the road traction signal which is obviously due to the 4WD system when I checked the manual. Please what’s the solution?

The AC is not blowing as much as the Corolla I use what could be the cause as well?

MotorGuru:

at your location i cant unfortunately.

pls can i hav ur contact sent to lawalmutiuolalekan@gmail.com or 08039154846. Pls i need to talk to you.

Hello Car guru, I have 2005 Honda accord, each time I engaged it to D it will start vibrating and if I remove it from D to N even with AC on it becomes normal.. Kindly advise me? I have changed all the engine seats...

MotorGuru:


Valve stem seals could be bad. replace them and get back to me.

i eventually found an engineer. He said, dere is a very high tendency for d car to start smoking if the valve stem seals is replaced. So therefore it must be ringed along side d valve stem seals replacement. How tru sir.

Hello motorguru, thank you for outstanding support.
Pls I uses 2007 honda pilot with an issue of high fuel consumption, after scan it generated a code P0 172 and later generated another code, P0 430. Now the car no more accelerate faster as it use to.

On P0 172, I've worked on the injectors and they are OK, checked for exhaust leakage and it's OK, I've not changed any sensor yet.

Pls I need your assistance.

efizyhenchmen:
Hello Car guru, I have 2005 Honda accord, each time I engaged it to D it will start vibrating and if I remove it from D to N even with AC on it becomes normal.. Kindly advise me? I have changed all the engine seats...

Recheck all engine seats. Ensure the ones replaced are originals and not Chinese clones.
scan vehicle if there is any check engine mount and ensure that the active engine mount vacuum supply( located in front of engine ) is in good working order

Makawhizzy:
Please my liberty Jeep 08 shows check engine on dashboard and after scanning we found out catalytic converter and O2 sensor needs to be replaced. I bought new ones and they were replaced. Fuel consumption reduced and no more noise from exhaust but the check engine signal is still on and three new lights are on which are service 4WD and I can’t change from 2WD to 4WD Plus the road traction signal which is obviously due to the 4WD system when I checked the manual. Please what’s the solution?

The AC is not blowing as much as the Corolla I use what could be the cause as well?

Scan the vehicle for codes.
for ac, check operation of condenser fans, ensure condenser is not blocked, check refrigerant charge.

babyboy4every1:

i eventually found an engineer. He said, dere is a very high tendency for d car to start smoking if the valve stem seals is replaced. So therefore it must be ringed along side d valve stem seals replacement. How tru sir.

he is recommending a complete overhaul of engine.
the choice is yours sir.

Bright2:
Hello motorguru, thank you for outstanding support.
Pls I uses 2007 honda pilot with an issue of high fuel consumption, after scan it generated a code P0 172 and later generated another code, P0 430. Now the car no more accelerate faster as it use to.

On P0 172, I've worked on the injectors and they are OK, checked for exhaust leakage and it's OK, I've not changed any sensor yet.

Pls I need your assistance.

for the P0430, ensure your catalyst is not blocked.
That can cause acceleration problems

MotorGuru:


for the P0430, ensure your catalyst is not blocked.
That can cause acceleration problems

Thank you for your reply, incase the catalyst is not blocked what else can I be looking at to solve this problem?