SULIEMAN3: tanx alot.

olenyi:

Warm Regards.

Xpset: hello gurus in da house.
l want to no if l can track Badr 4 @
26.0°E with 60-90cm dish to get the
list of frequencies listed on this link
http://
dvbfrequencies..com/2012/12/
badr-4-latest-update-freq-satellite-
tv.html?m=1
thanks in advance

olenyi:

If u have money, say around 10k, u could get an mpeg 4 decoder like srt 4669x or 4669x11, or 4322 and use ur dish to pick multi tv, where u get steady movies, nigerian movies, aljazeera, bbc, music, etc. Ur best bet. Regards.

Echika China: Please, I need your help, I have strong decoder 4669 11, I use to watch multi tv. During the change of frequency on 27 nov, I did as they instructed by putting 12522 V 19531, .... I did manual scan and got 16 station. This is the first time I ever entered the setting area of the decoder, . I enjoyed the 16 stations for 2days and the all disappeared, all became red, after some time, I got frustrated and went to the dish setting and put the 12522 V 19531. I also did same for motorised setting, PID scan and OTA menu.
Since then, all my multi tv remained red. I am confused, I dont even know the numbers that I deleted in order to put this new one. Like I said, this is the first time that I ever entered the installation area of the decoder. l will appreciate any help. what should I do.
Thanks

SULIEMAN3: ota, pid scan should be leaved and go to manual scan and input this tp12523v19531 pres exit to save nd blindscan. provided the dish has not been touched.

Echika China: I have already changed the setting in PID, OTA and DISH SETTING. I have tried what u suggested severely but no luck. Thanks for ur response bro

olenyi:


How many dishes are using. First of all, go to menu - system settings - factory reset. Enter four zero's if pin required.

Afterwards, if u are using two or more dishes, go outside and check which diseqc port number is connected to which satellite. (if u have any dish dat looks like its facing up, dats for multi tv. If dia's one dat is almost vertical, dat one is for emmanuel tv and co. So note the port numbers on the diseqc switch)

Not put on ur receiver, press menu, press ok, enter 4 zero's if required. Select dish settings if u are using more dan one dish. Scroll through the satellite names until u get to ''astra 2abd''. Go to disqc settings and set the port number for multitv first. Afterwards press exit once.

(If u're using one dish or after the above procedure)

Scroll down to manual scan. Check the satellite name for astra 2abd. Go down to frequency and press ''0''. Select edit and enter 12523 for frequency, 19531 for symbol rate and ''v'' or ''h'' for polarization depending on how ur dish was set. It should change to green now. Press ok to scan. Exit afterwards.

If u have two dishes and u were getting emmanuel tv before, now repeat above instructions but dis time look for ''intelsat 7/10 ku'' and set the diseqc port number. Go to manual scan and scan these frequencies

12772 h 26657
12552 h 26657
12772 v 26657
12682 h 26657
12578 v 03100
12572 h 26657
12601 v 26657.

Regards my brother. Kindly come back for more if u run into any difficulties.

Regards once more.

SULIEMAN3: oga olenyi weldone, u have made everything clear and easier for him.

RedReact: @Olenyi,
If u were to be a teacher, walahi, students no go read extra again cos ur explanation would be enough to make them understand.
Kudos to u sir.

RedReact: @Olenyi,
If u were to be a teacher, walahi, students no go read extra again cos ur explanation would be enough to make them understand.
Kudos to u sir.

SULIEMAN3: ah! Olenyi time is extraordinary.

SULIEMAN3: ah! Olenyi time is extraordinary.

RedReact:
I can only pray God's blessing on him. He displays astute intelligence and derives joy in solving problems.
He went ahead to explain an issue like that and such response of his got me saying technical jargons.
God bless u oga.

olenyi:

U'll most probable have to get a new 4 port diseqc switch.
Go ahead and get the extra dish for mbc. U can get the signal.we will be here to guide u through.
Can u list out some of the channels u're getting. Apart from the mytv/church channels and joytv/cine afrik and co, what other channels are u getting? Regards.

guseman:

@Oga Olenyi
I bought the 90cm dish yesterday and all the accessories. I will try and fix it later today,been busy in the office but am free abit now. So where do I start from?

NB: I bought strong LNB cos d guy selling it recommended dat it is good, but going tru your comment I realized you indicated that I should not buy strong LNB. Let me see wat I can do

olenyi:

W3a in a way faces south. It is above multitv. But we will first track astra 4a @ 4.8'east.
This is how u track it.


Go to ur dish. Dia are two screws on both side dat u use to tighten the dish to ur desired elevation.
Now loosen the one on top on both sides. On close observation, u will notice their are two holes provided for the screw. Remove the top screw from the first hole and refix it in the inner one. (this will allow the dish attain the desired elevation in other to hit 4.8'e)

Now track joytv with 12523 v 19531 on astra 2f @ 28.6'e. Optimize the signal to the best u can get.

Now input 12015 v 29950 and standing at the back of your dish, start tracking the signal in this format.
While keeping your eyes on the signal on ur tv, raise ur dish vertically until it is almost facing the heavens, bring it down again. Shift the dish horizontally a bit to the right, raise up vertically again, down,
Again a bit to the right, up and down. A little to the right, up, down. Keep at it until the dish is like its faceing south.

Continue in this way and u should hit green. When u hit grenn, fine tune ur dish until u get the highest % u can get. Tighten.

Now input 11192 v 03210. play around dat position and u should hit green. Fine tune once more and blindscan.
Pheeeew!!! Hope this helps. If u hit any difficulties, feel free to ask and we shall help out.

My best Regards.

jman77: @olenyi,good job you 've done here. I've been off here for a while and happy to be back,viva FTA

olenyi:

guseman:

You are just too wonderful. I will try dat later today and give u feedback later.

Merry xmas in advance

guseman: @olenyi
I am abt to start the tracking,do I need to disconnect the other 3 LNB's?

olenyi:

Yes. It would be better. Run the wire direct to the rx without the diseqc switch in between. Regards.

guseman: After tracking the 90cm dish,I was able to get 90% signal strenght the I went to dish setting to enable the port,that is where I mess things up.

I reset d rx and it worked but intelsat 7/10 not longer avail.

I have been trying to set it up but till now no luck.

okoegualek:

@Olenyi,can u pls pm ur fone numba or BB pin,u are jst 2 much jooooor.Thanks 4 d way u answer questions here,wish evry oda person here in d forum would do as u do alwzs

guseman: After tracking the 90cm dish,I was able to get 90% signal strenght the I went to dish setting to enable the port,that is where I mess things up.

I reset d rx and it worked but intelsat 7/10 not longer avail.

I have been trying to set it up but till now no luck.

habib55: . Same happend 2 me a while back,wen i reset my rx .intelsat1oku wil change 2 intelset20ku.so jst use d intelsat 20ku nd input ur tp nd change ur port settings

guseman:

Bros I tried that but wen I tried inputing 12523 and changing symbol rate to 19531 it kept saying TP exist already.

I need help guys,I refuse to call d installer...madam dey halla but mionigba...